Sewn in the good ol' USA, this came via Keith, the best parts man Intermountain Chevrolet ever had .... Worth it ... PM, please ...
This is a good one. No cracks, no pitting. Good threads. Stainless bars have wear into base indicating use by a real cool guy .... Patina, too - has 2 tiny car lighter burns on border. Shipping best way, usually priority. PM, please.
Tips from the beer truck drivers in the late '60s - take good care of their trucks & they remembered ... 3/8'' USS threads, none have been mounted. $35 each. PM, please
This is a good one. No cracks, no pitting. Good threads. Stainless bars have wear into base indicating use by a real cool guy .... Patina, too - has 2 tiny car lighter burns on border. Shipping best way, usually priority. PM, please.
Really nice 2 tone green Cad 62 series wheel, was marked '51-'52. Has the typical dozen or so age shrinkage cracks, but it isn't flaking & brittle. Nice shiny chrome with a few tiny pits, cap very nice. Big GM spline, won't fit Chev, Olds, Pontiac, or trucks. $150 plus shipping ... PM, please ...
Fairly nice bright red wheel from a Century. 1/2'' crack in horn ring spoke at 2 o'clock. Light freckly pitting in chrome, should polish to decent driver quality. Plastic is not brittle or flaking, cap is cloudy. The turn signal cancelling pegs were cut for some reason. The spline is the big GM, won't fit Chev, Olds, Pontiac, or trucks ... Wire & string were for hanging ... $100 plus shipping, ...
Here's a distributor driven tach-vac ... back lit, convex glass, bright colors, was mast jacket mounted but looks to be designed for in dash installation. The large index key on the dist. pickup suggests it was used with an Autolite dist. - it was installed on a '48 White WB 20 Army bus if that helps any. Not tested with the exception of the vac. gauge, which works. Some light pitting on the ch...
671 Detroit Engine with Allison Auto trans. Unknown mileshourscondition. Comes with parts body only, no title, 6 wheels so it can be loaded. Been sitting for a several years, not driveable, must haul away. First $2000 or Best Offer.
Rebuilt High Pinion 78-79 Ford Dana 60. Drivers side drop. All new internals, kingpins, yoke, and brakes. 4.10 gear ratio. Direct swap into 73-87 squarebody for drivetrain conversion or old dentside Ford.208-390-sixtwothreeone
I have a new no sway Anderson hitch 2 516 ball and 4inch drop kit..I had got this for Christmas and never used it and need the cash.i will not go lower they are over 500contact Jeffrey text
For Sale Used BB Mag. Buzzer. $50.00 O.B.O. For more Info. or Questions Call If I dont pickup PLEASE leave a message I will return your call ASAP
2012 Ford F-250 front bumper bolts and brackets taken off when truck came off the lot $15020 eight Two four zero 511two2011 2012 2013 2014 2015 2016 powerstroke diesel f-350 Cummins duramax
This is a 1995 Ford ranger XL. This is a great little truck to have. This fall I have replaced the slave cylinder, master cylinder, hydraulic hoes for the master cylinder, pilot bearing, fly wheel, clutch plate, release Bearing. It also has after market Dual speakers, a pioneer stereo, Newer discoverer st tires, and a brush guard. This is a 5 speed manual.Contact for more information. Thanks
Original Ford round dial radio. No idea if it works or not but, itll fill that round hole in your dash.25. OBO. Steve- 20eight five 2 one 8 4 seven 8.
A decent pair of headlight buckets. Top trim intact, pre-customized with authentic bullet holes in one. Good, repairable condition for a restoration or rat rod ready.Steve - two o 8 5 2 one 8 four 7 8. 100. OBOIf the ad is up, they are available.
Looking to sell the engine out of my 2005 Yukon. Its complete and fully ready to go into classic truck or replacement for your stock setup. Its pulled and ready to go into your hot rodIt is the 05 setup, so it has flex fuel capabilities if you wanted to use it5.3L engine - fully dressed with all accessories200k miles - had great oil pressure, didnt smoke and ran greatWiring harness, gas pedal a...
New Seat covers never been used for a Chevy Silverado. Front seat covers is for a 40 20 40 split. The back seat cover is for a solid bench seat. They are made of a neosupreme material. This material is lighter than neoprene and is water and stain resistant. They will also fit the GMC Sierra. I have attached one picture and can send others if interested. I am asking $300 OBO. Would be willing to...